My cleaner does not move

Detergents will depend on several factors, in order to make them work. There must be enough water flow past the turbine. Use a vacuum gauge to the vacuum tube in measurement. You have to be "1" to empty for the section of pipe.

Second, the four small "shoes" could surface swimming plug. Make sure the shoe "," is not exhausted and that the surface of the pool is not slippery because of algae building. Note: some algaeclearly you are sure to hear the pool water surface.

Thirdly, the shoes and "pods" works well. Signs of wear on the train "guide" can cause problems. To try to wear, hold the left and right "pods" in your hands and lay people, trying to rock the pods. All power to the turbine at a trot and not "play" can be transferred visible.

As a test, hold the cleaner hose. Keep the cleaner below water with the pump. Keep clean the bottom of thepool and observe, the cleaner: do not turn right – again – turn left – not rotate – rotate right – etc. All the time, the pods' that kicks. If you can not come clean and stop pods by hand, or there is excessive wear on internal parts or inadequate suction. I remember the emptiness of reading for the control before calling for help.

The tubes are Kink

Cleaner hoses can not be rolled up for storage. If you have them, takesections apart and put it away, and leave them out for a day and a night. Once the curls have been removed, the tubes used.

Detergents climb the wall of my pool vinyl siding

Depending on the plan for swimming pool walls, the cleaner may not be able to "climb" the slope. "Photo of cleaner on the bottom of the pool at the intersection where the wall meets the bottom of the pool at an acute angle (asthe walls of the house.) The cleaning lady will not be able to make the transition, do not worry, it is due. After all the dirt on the bottom.

The cleaner sticks at work

The tube may be too short.

Monitor to verify that the pipe goes two full pages over the farthest point in the pool.

To see what the return line (s) is not cleaned the movement involved.

Use the vacuum gauge for the vacuum tube in measurement. You should have1 inch vacuum per section of pipe.

Look at the shoes, wings and flaps for wear.

Check the rear flap surgery, and move my position.

As a test, hold the cleaner hose. Keep the cleaner below water with the pump. Keep the cleaner from the bottom of the pool and observe, the cleaner: turn right – not rotate – left-handers are not – yet – right – etc. All the time, the pods' that kicks. If the Detergent not "test"movements, called Blue Haven Pools & Spas Supplies Direct.

My cleaner floats above the floor of the pool

The cleaner is heavier than water, and should not float.

Make sure all air is removed during installation of the head cleaner and hose.

Sure that the hose extends two full sections beyond the farthest point in the pool.

Use the vacuum gauge for the vacuum tube in measurement. You have 1 centimeters empty sectionhome.

To see that the return line (s) are not charged for socks clean or less polluting.

Look for signs of air back into the pool through the return line (s) found. A second air bubbles in the pipe cleaner and the head. If so, draw heavily on cleaner hose to release bubbles. Then the source of loss is not sufficient to avoid more "fluid".

My cleaner moves slowly
Look at the shoes, wings and flaps for wear.

Check for obstructions incleaner.

Use the vacuum gauge for the vacuum tube in measurement. It should be 1 centimeter for each section of the vacuum tube. If the cleaner is still moving slowly, called Blue Haven Pools & Spas Supplies Direct.

The pods in front of the cleaner are worn

The wand cleaner at work or on a wall. See the section clean adherent scale above.

Cleaner rises to the surface and sucks air
Vacuum is probably too high. Use the vacuum gauge formeasuring tube of a vacuum cleaner. You have 1 centimeters blank for each section of pipe.

Check the rear flap surgery, and move my position.

Look at the shoes, wings and flaps for wear.

As a test, hold the cleaner hose. Keep the cleaner below water with the pump. Keep the cleaner from the bottom of the pool and observe, the cleaner: turn right – not rotate – left-handers are not – yet – right – so if the cleaner is at a turning point, calledBlue Haven Pools & Spas Supplies Direct.

The bottom of my cleaner is worn

The shoes are worn, and the difference in the pipe cleaner is probably too high. Use the vacuum gauge for the vacuum tube in measurement. You must be a '1 'is the blank for each section of the pipe. Replace worn out shoes.

The upper part of my cleaner will not spin

Will not be able to turn cleaner top when the cleaner is full of water. Drain the water from the head cleaner and try to reverseBoth left and right at the top – there may be some debris in the gears. If the top does not rotate, called Blue Haven Pools & Spas Supplies Direct.

Air in my pool when the cleaner is installed, and stops when the cleaner is removed

There was a leak on the suction side of the filter system that appears only when the system under stress. ie – install your manual vacuum cleaner or an automatic vacuum cleaner. Check for obvious leaks in the pump body, checkcover and O-ring. As the air continues, contact Blue Haven Pools & Spas Supplies Direct.

The flappers / wings fell

There are more wear on the bottom of the cleaning device, and the wing hooks have probably broken impulses. The shoes are worn, and the difference in the pipe cleaner is probably too high. Use the vacuum gauge for the vacuum tube in measurement. You must be a '1 'is the blank for each section of the pipe. Replace worn components.